Ambassadors

1. Remove valve cap, o-ring and lock nut
2. Insert valve through valve hole in rim
3. Push the o-ring onto valve stem
4. Thread the lock nut onto valve stem
5. hand tighten lock nut until firm
6. Screw on valve cap

Whether you’ve lost a valve cap or just want to bling your existing pair of peaty’s valves, this kit gives you everything you need.

Package contents:
1x spoke key cap (for 3.4mm spoke nipple)
1x valve core remover cap
2x lock rings

Compatible with all Peaty’s Tubeless Valves

Reuse. Refresh. Recycle.

Did you know we also make maintenance kits with fresh o-rings, rubbers & valve cores?

Designed by pro riders, mechanics and scientists, Peaty’s Tubeless Rim Tape has been developed from the ground up as a bicycle rim tape.

AVAILABLE SIZES

21mm, 25mm, 30mm, 35mm

** All Peaty's Tubeless Rim Tape's come in lengths of 9 meters / ~10 Yards! **

The super high tensile strength tape is primed with a bespoke adhesive which clings like s**t to a blanket.

An optimum amount of stretch and large rigid recyclable core allows the tape to be pulled and applied with tension, contouring your rim tightly for a better fit.

Do you struggle to find the hole? No problem!
Just hold your rim up to the light and the tape’s semi-transparent finish will illuminate the way.

Fitting instructions:

1. Remove tyre and any old rim tape
2. Clean and degrease rim thoroughly
3. Ensure rim is completely dry before application
4. Press tape firmly into the centre of the rim and smooth out to the edges, removing any trapped air
5. Run tape around the rim while keeping tape tension and allowing for at least 10cm overlap of tape at the end when cut
6. Use a small spike to pierce the tape in the centre of the valve hole
7. Remove dust cap and Push valve through the valve hole
8. Apply lock ring tightly by hand, ensuring there are no air gaps
9. Refit tyre, add Peaty’s Tubeless sealant, inflate Tyre
10. Ride!

Born in the lab and raised between the tapes, Peaty's Link Lube is a minty fresh, triple distilled, ultra high speed chain oil for use in all conditions.

Our unique formula penetrates and cleans deep inside your chain, driving out moisture, grit and grime and replacing them with unique blend of oils and waxes (Peaty's secret sauce) to lubricate and protect.

Yes, you read that correctly!

Peaty's Link Lube actually cleans your chain as you use it!

Application

1. Always fully degrease your drivetrain before applying fresh lube. For best results, use Peaty's Drivetrain Degreaser. 
2. Ensure you thoroughly wash your chain with clean water after degreasing (degreaser is designed to eat chain oil after all). 
3. Remove as much water as you can from the chain - a quick wipe with a clean cloth will do fine. 
4. Give the bottle a good shake to evenly distribute the secret sauce. 
5. Apply the lube while cycling the chain backwards (eBikes will need to be pedalled forwards in a stand) ensuring every link is adequately covered. 
6. Keep cycling the chain for 10seconds or so to help the lube work its way into your chain. 
7. Thoroughly wipe away all excess lube from your chain using a clean cloth (excess oil on the outside of the chain will attract dust in dry conditions).

Tips:

1. For wet weather conditions, leave a small amount of lube on the outside of the chain for longer-lasting protection.
2. On first use with pre-used chains, you may find that your chain turns black - this is the LinkLube driving out grime from deep in your chain. Just keep riding, degreasing, lubing and repeating until your chain runs shiny clean once more!

Caution - Do not get LinkLube (or any lube for that matter!) on your brakes or brake pads.

Buy one bottle of Loam Foam Concentrate and get a single one liter bottle of ready-mixed Loam Foam. This bundle will make six litres of professional grade Loam Foam Bike cleaner.

Once diluted, you will get the same foamy cleaning power that you get with the ready-mixed Loam Foam you know and love, but use 80% less plastic and take up much less space in your workshop

Bundle Includes:

• 1 x 1L / 34oz Loam Foam Concentrate (Makes 5L Loam Foam)
• 1 x 1L / 34oz Loam Foam + Spray Head

Mixing Instructions:

1. Pour 200ml of Loam Foam Concentrate into an empty Loam Foam spray bottle using the markers provided on the side of the concentrate bottle.
2. Top up the bottle with fresh cold water, up to the shoulder of the bottle.
3. Replace the sprayer and tighten until firm.
4. Shake the bottle vigorously until fully mixed.
5. You're ready to go!